| Target: | Mouth odor:C2H5OH、H2S、CH3SH |
| Model: | MQ316 |
| Detection range: | C2H5OH(5-200ppm) |
| Detection principle: | Semiconductor |
| Characteristics: | High sensitivity to C2H5OH、H2S、CH3SH |
| Size: | φ9.4×8 |
| Working conditions: |
Loop Voltage：3±0.1V Heater Voltage：0.9±0.1V Heater consumption：≤150mW |
MQ316 Manual download
Get Price Whatsapp
Description
The gas-sensitive material used in the MQ316 odor sensor is a semiconductor material with low conductivity in clean air. When there is a gas to be measured in the environment where the sensor is located, the conductivity of the sensor increases as the concentration of the gas to be measured increases. Use a simple circuit to convert the change in conductivity into an output signal corresponding to the gas concentration .
Application
Widely used in breath odor detectors, portable alcohol detectors, etc.
Features
Widely used in breath odor detectors, portable alcohol detectors, etc.
Specifications
| Model | MQ303B | ||
| Sensor Type | Semiconductor | ||
| Standard Encapsulation | Metal | ||
| Target Gas | Alcohol gas | ||
| Detection range | 20~ 500ppm alcohol | ||
| Standard Circuit Conditions | Loop Voltage | V H | 0.9V±0.1V AC or DC |
| Heater Voltage | V c | ≤6V DC | |
| Load resistance | R L | Adjustable | |
| Heater Resistance | RH | 4.0Ω±0.5Ω（room temp.） | |
| Heater consumption | PH | ≤140mW | |
| Sensor character under standard test conditions | Zero point | V0 | 0.01~0.45V |
| Sensitivity | VS | 1.0~2.5V (in 125ppm C2H5OH) | |
| Concentration Slope | α | ≤0.6(R300ppm/R50ppm C2H5OH) | |
| Standard test conditions | Tem. Humidity | 20℃±2℃ 55%±5%RH | |
| Standard test circuit | Vc:3.0V±0.1V DC VH:0.9V±0.1V DC | ||
| Preheat time | Not less than 48 hours | ||
* The description and specifications might be changed without notice. Please contact us for the latest information before placing orders.
Technical Support:
Customized technical design and function, LOGO and package are available without extra charge (including molding fee) for mass volume.
The sensors don't have sleeping mode. It can be set in program if needed.
All Winsen products go through strict inspections and tests to make sure they are 100% qualified before shipping out.
The sensor has been fully tested (not calibrated) before leaving the factory, but the module will be calibrated before leaving the factory.
However, after transportation and storage, the environment conditions change, and the surface of the sensor absorbs moisture, mixed gas, pollution matters, etc. It is recommended that customers perform aging and calibration after sensors become stable according to the program and use occasions of the whole device.
15﹪-90﹪RH without condensation,greater or less than this range or long-term high temperature and high humidity will affect the life of the sensor.
Our sensors are certified with CE, 3C, ROHS, anti-explosion, fire prevention, and coal mining safety according to different applications. And we provide assistance for new certification.
Many factors can cause the sensor to fail such as broken wires in transportation, poisoning, falling off of the sensitive material, damage to the heating wire (device), etc. Please find specific cause in each category with Winsen’s aftersales.
Winsen provides professional consultation and service before and after sales. We will recommend the best fitting sensor for your demand. If you have any problem, don’t hesitate to email us to sales@winsensor.com
Due to high volume of daily incoming emails and time zone difference, we may not be able to reply your emails immediately. But we will reply to your inquiry in 24 business hours.
