| Target: | refrigerant gases：R32、R134a、R410a、R290 |
| Model: | MP510C |
| Detection range: | 100-10000ppm |
| Detection principle: | Semiconductor |
| Characteristics: | Can detect kinds of refrigerant gases |
| Size: | φ9.05×12.5 |
| Working conditions: | Loop Voltage：5±0.1V Heater Voltage：5±0.1V Heater consumption：≤300mW |
MP510C Manual download
Get Price Whatsapp
Description
The MP510C Freon gas sensor uses a multilayer thick film manufacturing process to fabricate heating and measuring electrodes and a metal oxide semiconductor gas-sensitive layer on a miniature Al2O3 ceramic substrate, and encapsulate it in a metal casing. When the detected gas exists in the ambient air, the conductivity of the sensor changes. The higher the concentration of the gas, the higher the conductivity of the sensor. This change in conductivity is converted into an output signal corresponding to the gas concentration through the circuit. The product has good anti-interference ability against common gases such as alcohol and acetic acid in usage scenarios.
Application
Used for leak detection of refrigerants in air conditioning and refrigeration systems
Features
- High selectivity, fast response, good anti-interference, long lifespan, good stability
- Can detect kinds of refrigerant gases R32, R134a,R410a,R290.
Specifications
| Model | MP510C | ||
| Sensor Type | Semiconductor flat surfaced sensor | ||
| Standard Encapsulation | Metal Cap | ||
| Detection Gas | Refrigerant gas | ||
| Detection range | 100～10000ppm | ||
| Standard circuit | Loop voltage | VC | 5.0V±0.1V DC |
| Heating voltage | VH | 5.0V±0.1V DC | |
| Load resistance | RL | Adjustable | |
| sensor features in standard test condition | Heating consumption | PH | ≤300mW |
| Surface resistance | RS | 0.5～10KΩ(in 5000ppm R32) | |
| Sensitivity | S | 0.3~0.7 (R32) Rs(in 9000ppm)/Rs(in 3000ppm) | |
| Standard condition of test | Temperature, humidity | 20℃±2℃；65%±5%RH | |
| Standard test circuit | Vc:5.0V±0.1V； VH:5.0V±0.1V | ||
| Warm-up time | 7 days | ||
* The description and specifications might be changed without notice. Please contact us for the latest information before placing orders.
Technical Support:
Customized technical design and function, LOGO and package are available without extra charge (including molding fee) for mass volume.
The sensors don't have sleeping mode. It can be set in program if needed.
All Winsen products go through strict inspections and tests to make sure they are 100% qualified before shipping out.
The sensor has been fully tested (not calibrated) before leaving the factory, but the module will be calibrated before leaving the factory.
However, after transportation and storage, the environment conditions change, and the surface of the sensor absorbs moisture, mixed gas, pollution matters, etc. It is recommended that customers perform aging and calibration after sensors become stable according to the program and use occasions of the whole device.
15﹪-90﹪RH without condensation,greater or less than this range or long-term high temperature and high humidity will affect the life of the sensor.
Our sensors are certified with CE, 3C, ROHS, anti-explosion, fire prevention, and coal mining safety according to different applications. And we provide assistance for new certification.
Many factors can cause the sensor to fail such as broken wires in transportation, poisoning, falling off of the sensitive material, damage to the heating wire (device), etc. Please find specific cause in each category with Winsen’s aftersales.
Winsen provides professional consultation and service before and after sales. We will recommend the best fitting sensor for your demand. If you have any problem, don’t hesitate to email us to sales@winsensor.com
Due to high volume of daily incoming emails and time zone difference, we may not be able to reply your emails immediately. But we will reply to your inquiry in 24 business hours.
